About this deal
AmpliFi will not replace your cable, DSL, or fiber modem. You need a modem to bridge the connection between your service providers internet service and your home router and devices. Note that AmpliFi provides the hardware, not the internet service. AmpliFi is also compatible with fiber optic services. Bootup state: The router LED will be lit at the minimum brightness setting. The bottom LED of the MeshPoints will be lit for 15-20 seconds, and then the LEDs will light up in sequence from bottom to top for 10-15 seconds. AmpliFi Instant WiFi System (AFI-INS): Includes a router with an easy-to-use touchscreen display, 1 Gigabit Ethernet port, a WAN port, an Ethernet cable, and one MeshPoint with an Ethernet port to maximize coverage and eliminate dead zones in your home. I’ve tested a lot of Wi-Fi mesh (aka whole-home coverage systems) products lately, but what if you already have a good Wi-Fi router and don’t want to do a rip-and-replace job? There’s a new device available aimed just at this purpose. If your mesh point(s) have disconnected themselves from your router, the pairing protocol might need to be realigned between the mesh points and the router. The troubleshooting steps are different for mesh points that came with the router in the AmpliFi HD kit (AFI-HD) for example and the mesh points that are sold separately (AFI-P-HD). Please find the troubleshooting steps for each type of mesh point below. This article applies to all our product lines (AmpliFi HD, Instant, Gamer and Alien lines).
AmpliFi AmpliFi
If you notice slow speeds on both wired and wireless devices or only wired, please proceed to the troubleshooting steps below: Pair the MeshPoint with the AmpliFi™ Router to expand the coverage of an AmpliFi™ network or turn an existing router into a powerful mesh network. amplifi, afi, afi-p, afi-p-hd, afi-p-hd-uk, afi hd, amplifi mesh, amplifi hd mesh, amplifi wifi , afi uk, afi r uk, amplifi repeater
Removing restrictions to pair AmpliFi HD (AFi-P-HD, AFi-HD-R, AFi-G) family devices to AmpliFi Alien. * In my case, the mesh point was using the 2.4GHz band to communicate with the router, as that was the only option. Had the router been dual-band, I could have chosen either frequency band. Ready state: The router LED will be lit solid white at the maximum setting or at the brightness level you choose in the AmpliFi app. The MeshPoints will be lit based on the signal strength that they are receiving from the router.
Ubiquiti Amplifi 4-Ports Home Wi-Fi System AFI HD Wireless
This is pretty decent performance for such a small router with no external antennae, and shows how you don’t necessarily have to have a big bulky router in the vein of the Linksys WRT32X to get good coverage. Tip Alternatively you can look at the status LEDs on the MeshPoint and verify that all five LEDs are illuminated, meaning it has 100% signal level. Less than five LEDs would indicate a signal less than 100%.The main screen on the LCD display will have the time and date. You can choose between 12h and 24h mode in the app by launching the AmpliFi app, and selecting the router icon to access its Settings. Then navigate to General > 24-Hour Time. By default, AmpliFi Alien has WiFi-6 enabled in the primary SSID. If you would like to separate the 2.4GHz and 5GHz bands into individual networks, you can do so by disabling Common SSID Name. An example of when you would want to disable the Common SSID Name would be when you want to prevent your devices from roaming between the 5GHz and 2.4GHz networks. By disabling this feature and connecting your device to your desired network, you make sure they do not move from that band. Even though the mesh point was in the same room as the router, the ISP speed test was a miserable 7 Mbps down and 4 up. My Android device, while connected to the mesh point, tested at 5 Mbps down and 5 up using the Speedtest.net app. Later, it tested at 16 Mbps down and 12 up. An easy way to connect to your device is by enabling WPS (Wi-Fi Protected Setup). If your device supports WPS, then you can enable it on AmpliFi by following the steps in this article. After the mesh point(s) has been factory reset, perform the same step on the router. It is important that the mesh point be factory reset before the router. The router can be factory reset through the AmpliFi smartphone app settings or by inserting a paperclip into the factory reset pinhole located at the bottom of the router. Hold down for five seconds until the front screen of the AmpliFi router says "Rebooting...".
AmpliFi MeshPoint HD – Amplifi Wi-Fi
If neither of these work, you can clear the network history of the device. This has been noted as most helpful printers, but can help with any type of device that allows this sort of cleanup. This option can be found in most printer's main settings.
It’s definitely a gadget that you wouldn’t mind having out on display, rather than hiding it away like you’d want to with more ugly routers, which helps improve wireless strength, as it won’t have to battle through cupboard doors and other obstacles. When plugged in, the screen lights up, and a subtle white light along the bottom edge of the unit begins to glow.
AmpliFi HD Mesh Router – Amplifi Wi-Fi AmpliFi HD Mesh Router – Amplifi Wi-Fi
You can scan the QR code on the devices using the camera of your smartphone or tablet to view the MAC ID. For AmpliFi Alien, please continue reading to the next section. If you wish to configure the AmpliFi HD, AmpliFi Instant and AmpliFi Gamer's Edition , please skip to this section. AmpliFi AlienEach Ethernet port on AmpliFi will be displayed here. Highlighted means the port is active, whereas grayed-out means nothing is currently plugged into that port. Important If you are performing a factory reset on an AmpliFi kit versus a standalone router, you will need to factory reset the MeshPoints as well. Reset the MeshPoints first and then the main router. Physical Reset Tap the toggle to "Pause Internet on all devices". This will stop the internet access of all devices seen on the list. The kits cannot be used to expand single router systems, but standalone routers can be used to expand kits if compatible in the table below. While plugged into power, factory reset the mesh point(s) that has become disconnected. This can be done by inserting a paperclip into the factory reset hole and holding down the reset button on the mesh point power supply for ten seconds. You will hear a high pitched beep emit from the mesh point when the factory reset has been properly performed, or the bottom LED will be solid, while other LEDs are off.. Once you hear this sound, you can let go of the paperclip.