DYNAGEM polyWatch Watch Face Scratch Remover and Repair Polish

Product Information

As with all polishing, move through grits from coarse to fine, making sure that you remove all of the previous marks before moving on, and finished with Polywatch. Please excuse the dust... I will sometimes, depending on the watch, use a coarse as 400 grit to start - all done by hand and you do need to be careful not to overdo it. It looks worse before it looks better: old t-shirt .... moisten lightly with some finger's worth of water until it results in a "wet-spot" (insert dirty joke here) ... then a bit of the polish (fingernail sized drop) ... then I gently work the mustardy-paste into the wet spot until all the excess is in the fabric (about 2-3" across).

Polywatch is especially great for superficial hairline scratches as it doesn’t require a lot of grinding of the plastic material on the crystal. However, PolyWatch also works well for deeper scratches, although you need to apply more pressure and polish for a longer period of time. Usually I use masking tape around the bezel and edges to protect them. This is very important for gold-plated or filled watches as the chemicals tend to get underneath the plating and react with the base metal of the case.I believe that AR coatings are only applied to the inside of the watch crystal. If this is the case, then the scratches you are seeing are not to the coating, but to the sapphire itself. Sapphire is incredibly hard to scratch (bravo for finding a way to scratch it), but that also means it is equally as hard to polish. With the included polishing cloth, rub in a circular motion, with firm, constant pressure. The heat from the friction will allow the Polywatch to smooth out the crystal's surface. PolyWatch is a simple and reliable solution against scratches. The unique PolyWatch paste, which has proven itself millions of times, even removes deep scratches! It is not without reason that PolyWatch is the number 1 worldwide when it comes to watch polishes for acrylic glass. The innovative plastic deformation technology, which slightly softens the clear lacquer on the glass to fill in damaged spots, polishes away scratches and blemishes in an instant. Instructions

What I do is use microsandpaper, starting with 1800 grit and working to 12,000 grit, this allows me to remove virtually all the scracthes, as a final step, I use Polywatch. What Polywatch (or any other similar product) does is to use a super-fine grit to create enough friction to allow a tiny amount of plastic to melt into the scratches and fill them in. No - many are coated both sides. For removing outer AR coating I use diamond paste - fine so 0.5 or 1 micron will do the job with just dabbing a bit on the crystal and rubbing it with your finger. Plastic watch glasses scratch very easily and replacement is not always possible, particularly where the case is plastic. Polywatch slightly disolves and grinds down the surface of the plastic watchglass to smooth the edges of the scratch and fill the gaps with dissolved material.It looked very similar to your watch. It took me about 45-60 minutes and I was rubbing the crystal using polywatch really hard using the cloth that came with the polywatch. Would never rub it that hard on a hesalite. I have lenses scratched by my glasses. Both in the upper middle of the lens. You mention blur... and VR headsets are already blurry. Will using this just cause worse blur so that trying to look through the scratches might be better?

You must remove all scratches at one grit, before moving to the next, and eventually you will get it clear: No matter how careful you are, plastic watch glasses will scratch over time. This is mainly due to the position of the watch on the wrist, where it can easily scrape against a wall or other object. Unlike glasses, these scratches only detract from the beauty of the watch and not its function. However, it is annoying to constantly look at it. The product i just use a generic "polycarbonate headlight polisher" from pep boys or so - I had sitting around in the garage ... works just as fine ... never had a scratch that I couldnt get rid of One tube of PolyWatch can be used for approximately 10 watch crystals (depending on how much you use and how deep the scratches are).Sometimes you will notice that the crystal will look better 24-48 hours after treatment, than immediately after application. That's because you've given the fresh melted plastic a chance to harden. Polywatch® Glass Polish. High Tech Scratch Remover For Glass. Repair rather than replacing. Removes fine, light and medium deep scratches from watch glasses. Sufficient for approx. 30-40 applications. For use on cars, smartphones, watches, furniture, household, hobby, windows etc. Generally, polyWatch fills in the scratches. PolyWatch is a repair tool for watch scratches so the blur is a side affect. I have not tried using polyWatch on my lenses so don’t take my word for it but from what I know it shouldn't intentionally cause blur. When you are done, it will leave your acrylic or plexi crystal flawless and free of scratches, allowing perfect legibility onto the dial. The benefit of this is that you don’t have to replace your whole watch crystal in case it only has scratches. This is both a cheaper and more effective alternative.