Movies: Standard output sensitivity equivalent to ISO 160 – 12800 in increments of 1/3 EV; AUTO; extended output sensitivity equivalent to ISO 25600 My old original NP-W126 currently, after several years of usage, has roughly 1100 mAh, while it had >1200 mAh when new. Lower quality batteries can show more significant aging, the DSTE battery is already almost unusable. Conclusion This product information is fully applicable to the Fujifilm series compatible batteries, "Fujifilm battery NP-W126S". I don't think you will see any difference in the X-Pro2 because it was not designed to be take advantage of the features of the NP-W126s. For all versions of Fuji X ILCs except for the X-T2, the NP-W126 or the NP-W126s is the correct battery to use. For the X-T2, the NP-W126 will work if you don't use 4K video.

I also used my thermal camera, Flir One for Android ( iOS version exists too), to capture batteries after a heavy load. While the original battery shows mostly evenly distributed heat on its surface, the noname battery has much higher temperature in a smaller rectangle in the middle. This might be the reason for swelling of some batteries. Self-discharging mm × 92.8 mm × 58.8 mm (35.4 mm excluding projections, measured at thinnest part)/5.22 in. × 3.65 in. × 2.31 in. (1.39 in.) in., 3690k-dot OLED viewfinder; magnification 0.75× with 50 mm lens (35 mm format equivalent) at infinity and diopter set to −1.0 m−1; diagonal angle of view approximately 38° (horizontal angle of view approximately 30°)Well it's nice to know I can buy one of these more expensive NP-W126S batteries and use it in my X-E2 with absolutely zero gain in performance. Still pictures: Exif 2.3 JPEG (compressed); RAW (original RAF format, uncompressed or compressed using a lossless algorithm; special purpose software required); RAW+JPEG available

In terms of safety, I have no complaints at all with the Wasabi branded batteries. They don’t last as long as the Fujifilm, but they are consistent and the camera functions perfectly with them. The Dot-01 brand though, I do have concerns with and would not recommend. They get excessively hot when used for a whole shoot, and as I noted above, they (or at least the few that I have) have ceased to go in and out of the camera as smoothly as they should. It could be the two that I have, but they are the newest batteries in my kit, and they should not be doing this. All the batteries lose their performance with time and usage. Their capacity decreases and the internal resistance increases. Don’t expect the very same performance from few years old batteries as you get from the new ones. MHz (11 channels) in the case of the X-T3 WW. EF‑X8 shoe-mounted flash unit (not included with the X-T3 WW) Guide number I haven’t done any rigorous testing in this area, so far I’ve just tried to put all the brands to a fridge for few days, but haven’t measured any significant loss of charge. Even when not used for a long period, none of my batteries suffered any significant discharge. Battery aging Japan, China : 2,412 MHz–2,472 MHz (13 channels) * Other countries : 2,412 MHz–2,462 MHz (11 channels)It makes more sense to me that Fuji would have designed both of the Generation 3 cameras to take full advantage of the new battery they were developing, but that the battery might not have been ready for the X-Pro2 release. Looking to upgrade your equipment? Get competitive prices on major brands with our part-exchange service. Apparently the cheapest aftermarket batteries fail pretty bad, but fortunately many brands offer pretty solid competitors to the original batteries. They often have almost the same capacities and also heat management under a heavy load seems to be alright. HS50EXR HS30EXR HS33EXR Will this battery have any safety risks? What is the quality of the Fujifilm NP-W126S compatible battery?

This battery is made of top materials of Lithiumion cells that have been safely certified by RoHS, CE, FCC and tested through repeated simulated work and commissioning before they are shipped from the factory. On the other hand, its specifications are based on the original standards such as appearance, interface type, body size, capacity, voltage, charging current and voltage, etc. Is it real Fujifilm NP-W126S compatibility information? Lenses – Should have no marks on the elements andoptically clear. There may be light dust present that will not effect theimagery. The frame rate and number of frames per burst varies with shooting conditions and type of memory card used.

Bulk Order Enquiry

But what happens to my current OEM and Watson NP-W126 batteries if I upgrade to an X-Pro2 or X-T2? will they die a slow death from the extra heat generated in the new camera or just discharge a lot faster? Autofocus system: Intelligent hybrid AF (TTL contrast-detect/phase-detection AF) with AF-assist illuminator

I have used two of the readily accessible third-party brands here in the USA, Wasabi and Dot-01. As far as working, up until about 2 months ago, I was equally happy with both brands, but that is when the cheaper Dot-01 brand started to scare me. To the point that now I don’t use them in my X-Pro2 anymore. The Dot-01 batteries started overheating, and they no longer go in or out of the camera like the Fujifilm or Wasabi batteries do.

Condition guide

Cameras – LCD screen is heavily worn either by de-lamination or has scratches to it. Rubber grips are starting to come away from the body. In short, I don’t trust them. That said. I wanted to share my experience with these two third-party batteries compared to each other as well as to my original NP-W126 battery from Fujifilm. Run Time In Europe, there are very good Patona Platinum, Patona Premium and ExPro White. All of them offer >90% capacity of the original batteries and also they don’t seem to produce significantly more heat even after some heavy use. Submit a valuation request and we'll provide guide prices with no delay. Plus, we'll collect your gear from your home or work for FREE.