If you need to return a part then please telephone Di Vapor on 0121 705 0866 with the reasons for the return within 14 days of receiving the goods. The tray is then dropped into position, levelled and effectively glued into place and the trap is connected to the tray (the trap is already attached to the pipe as you have seen).

Slim Shower Waste - Low Profile | Victorian Plumbing

The first job is now seal up the gap between the shower tray and the wall. Using some suitable sanitary silicone, run a bead around both edges of the tray that butt up to the wall and then dampen your finger and use it to force the silicone down into the joint and then leave to cure. Not all shower trays are low profile, in fact, raised shower trays are very popular. They are great at keeping water from leaking out of the shower zone in your bathroom. Learning how to fit a raised shower tray is easier than fitting low profile options and perfect for beginners.In our example here we have had to remove a chunk of the floor as it was rotten so this has given us a good heads up on how the existing waste runs.

Slim Ø90 mm - Chrome Dome, the - Wirquin

This is never fully recommended as it can weaken the floor structure, unless further precautionary measures are taken. Toilets By Style Modern Toilets Traditional Toilets Corner Toilets Comfort Height Toilets Short Projection Toilets Sometimes the void under the floorboards beneath the shower tray is too full of pipework to run a waste pipe or to fit a shower trap.Tiles Bathroom Tiles Kitchen Tiles Floor Tiles Wall Tiles Vinyl Floor Tiles Porcelain Tiles Metro Tiles Marble Tiles Patterned Tiles With someone filling the waste for you, use a torch to inspect the waste trap and all the pipework for any signs of leaks. If there are any tighten any compressions joints as required.

Shower Tray | DIY Doctor How to Fit a Shower Tray | DIY Doctor

In answer to whether you should install a raised or flat shower tray, it depends on a few things – the type of floor you are installing on to, location of the existing waste if there is one and how much space there is available for the tray waste. Cut a hole for the shower tray waste. Ensure your measurements are accurate and once completed, proceed with assembly. Essentially the thing that stops you from fitting a shower tray flush to the floor is something that will stop you putting in the pipework and trap that carries away the waste water away under the floor……. This step-by-step guide will help to show you how to install a shower tray on a wooden floor using a low-profile tray. Please note, it is important that you read the manufacturers guidelines that came with your new tray.There will be two rubber washers attached to the waste (one for above the shower tray, and one for below), remove both. So there you have it! All being good you should have installed your new shower tray successfully. Do keep in mind that certain designs may need a slightly different approachso always read the manufacturer’s instructions. Fitting a tray (especially a low profile one) can be a challenge mind, so if you’re having any doubts about your abilities then we strongly recommend calling a plumber for this one. Alternatively, pipework above floor level (from a raised shower tray) can be run in behind a wall…. Once the tile adhesive had cured correctly the battens were removed leaving roughly a 2 inch gap that we could then tile once the ray was fully in place. For further help and advice on ceramic tiling, see our project here. Macerators All Macerators Single Toilet Macerators Cloakroom Macerators Full Bathroom Macerators Shower Lifting Stations Kitchen Utility Lifting Stations Flo-Force Macerators Saniflo Macerators Grundfos Macerators

Low Profile Shower Trays - Plumbworld Low Profile Shower Trays - Plumbworld

As mentioned already, you should always install your shower tray first and then tile down to it. Due to the extremes in temperature in a bathroom and the resulting expansion and contraction, everything moves a fair bit.

Due to the damp damage to the walls we had to remove quite a few tiles, not only as they were loose, but also to replace the damaged sections of wall. When learning how to lay a shower tray on a wooden floor, you will need to mark the area where the tray will stand. Next, replace the floorboards within that area with a minimum of 18mm marine ply.